Re: gEDA-dev: iverilog and xilinx xc4000 problem

[Stephen Williams <steve-at-NOSPAMicarus_dot_com>]

I recommend *not* using the xnf target. Use the -tfpga target,
which generates EDIF, instead.

Rich Cummings wrote:
> Hello,
> 
> Any help is greatly appreciated. Why am I getting this error?
> Assertion failed: 0, file t-xnf.cc, line 436
>  
> I'm trying to synthesize the below verilog code using this command line: 
> iverilog -pncf=myfirst.ncf -txnf -ppart=XC4005XL-3pc84 Counter10BitUp.v -omyfirst.xnf
> 
> Looking in the iverilog source code, it appears that draw_carry() is being called with an adder_type of FORCE0. So I guess this means it doesn't like the "Qout+1" in the code below.
> 
> Is my command wrong? Do I have to wait for iverilog to support "-t fpga" for xc4000? Should I just buck up and spend some money on a modern fpga? 
> 
> Any help is appreciated. Thanks in advance.
> 
> /////////////////////////////////////////////////////////////////////////////////////////
> iverilog version: Icarus Verilog version 0.8.4 ($Name: v0_8_4 $)
> hardware:        XESS XS40 v1.4 - w/ Xilinx XC4005XL-PC84
> 
> /////////////////////////////////////////////////////////////////////////////////////////
> // My 10 bit Up Counter - w/ Load
> module Counter_10Bit_Up ( Qout, Qin, Load, Clear, Clock );
>     output [9:0]  Qout;
>     input  [9:0]  Qin;
>     input         Clear;
>     input         Clock;
>     input         Load;
>     reg    [9:0]  Qout;
>  
>     always @(posedge Clock or posedge Clear) Qout = Clear ? 0 : (Load ? Qin : Qout + 1);
>     
> endmodule
> 
> module xr4005xl_counter ( qout, qin, load, clr, clk ); 
>     output [9:0]  qout;
>     input  [9:0]  qin;
>     input         load;
>     input         clr;
>     input         clk;
>     
>     wire   [9:0]  qin;
>     wire          load;
>     wire          clr;
>     wire          clk;
>     
>     Counter_10Bit_Up dut ( qout, qin, load, clr, clk );
> 
>     $attribute( qout , "OPAD", "0,0,0,0,0,0,0,0,0,0" );
>     $attribute( qin ,  "IPAD", "0,0,0,0,0,0,0,0,0,0" );
>     $attribute( load , "IPAD", "0" );
>     $attribute( clr  , "IPAD", "0" );
>     $attribute( clk  , "IPAD", "0" );
> endmodule
> 
> 
> 
> 
> 
> ------------------------------------------------------------------------
> 
> 
> 
> _______________________________________________
> geda-dev mailing list
> geda-dev@moria.seul.org
> http://www.seul.org/cgi-bin/mailman/listinfo/geda-dev


-- 
Steve Williams                "The woods are lovely, dark and deep.
steve at icarus.com           But I have promises to keep,
http://www.icarus.com         and lines to code before I sleep,
http://www.picturel.com       And lines to code before I sleep."



_______________________________________________
geda-dev mailing list
geda-dev@moria.seul.org
http://www.seul.org/cgi-bin/mailman/listinfo/geda-dev