[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: gEDA-user: I need to open and print a PCB created in ExpressPCB:What are my options?

To: "gEDA user mailing list" <geda-user-atMUNGEDmoria_dot_seul_dot_org>
Subject: Re: gEDA-user: I need to open and print a PCB created in ExpressPCB:What are my options?
From: "Mark Rages" <markrages-atMUNGEDgmail_dot_com>
Date: Mon, 29 Jan 2007 15:14:37 -0600
Delivery-Date: Mon, 29 Jan 2007 16:14:42 -0500
DomainKey-Signature: a=rsa-sha1; c=nofws; d=gmail.com; s=beta;h=received:message-id:date:from:to:subject:in-reply-to:mime-version:content-type:content-transfer-encoding:content-disposition:references;b=SqHKQUBrxj5RrlDsbIRpv0hC0Pg5sZ4WPKIsODOgVQv0O4IO7QXSRFvsEstYiPsQgsKzT+mDCJChluymmbpLDq6T72AN3MFriP8n1cZk9x+1fwfGqT9EFv/m/bWiL6E1Xt1xzYkMsKKgaLjAoVZcRAGsC0x3IhJQbl8LP+rJZL8=
In-Reply-To: <200701292110.l0TLAMvk016000@envy.delorie.com>
List-Archive: <http://www.seul.org/pipermail/geda-user>
List-Help: <mailto:geda-user-request@moria.seul.org?subject=help>
List-Id: gEDA user mailing list <geda-user.moria.seul.org>
List-Post: <mailto:geda-user@moria.seul.org>
List-Subscribe: <http://www.seul.org/cgi-bin/mailman/listinfo/geda-user>,<mailto:geda-user-request@moria.seul.org?subject=subscribe>
List-Unsubscribe: <http://www.seul.org/cgi-bin/mailman/listinfo/geda-user>,<mailto:geda-user-request@moria.seul.org?subject=unsubscribe>
References: <a21dfdb60701291255h4d00dc17gbadb8927b1cffc16@mail.gmail.com><200701292110.l0TLAMvk016000@envy.delorie.com>
Reply-To: gEDA user mailing list <geda-user-atMUNGEDmoria_dot_seul_dot_org>
Sender: geda-user-bounces-atMUNGEDmoria_dot_seul_dot_org

On 1/29/07, DJ Delorie <dj@delorie.com> wrote:
>
> > I have looked into gEDA and it looks very complicated at first
> > glance, yet very powerful -- like most things under Linux :-) --
> > what documentation should I peruse if I were to attempt this feat?
>
> The FAQ has a few key bits about symbol and footprint creation (also
> see www.gedasymbols.org), which is the trickiest bit of the whole
> process (*I* think it's easy, but it generates the most questions).
>

My usual way of learning software (just start using it and look up
features as I run into the need) was a total loss with gEDA.

The more structured approach of Bill Wilson's tutorial got me started, though.

Regards,
Mark
markrages@gmail
-- 
You think that it is a secret, but it never has been one.
  - fortune cookie


_______________________________________________
geda-user mailing list
geda-user@moria.seul.org
http://www.seul.org/cgi-bin/mailman/listinfo/geda-user

Follow-Ups:
- Re: gEDA-user: I need to open and print a PCB created in ExpressPCB:What are my options?
  - From: DJ Delorie

References:
- gEDA-user: I need to open and print a PCB created in ExpressPCB:What are my options?
  - From: Jeremy Pedersen
- Re: gEDA-user: I need to open and print a PCB created in ExpressPCB:What are my options?
  - From: DJ Delorie

Prev by Date: Re: gEDA-user: I need to open and print a PCB created in ExpressPCB:What are my options?
Next by Date: Re: gEDA-user: I need to open and print a PCB created in ExpressPCB:What are my options?
Prev by thread: Re: gEDA-user: I need to open and print a PCB created in ExpressPCB:What are my options?
Next by thread: Re: gEDA-user: I need to open and print a PCB created in ExpressPCB:What are my options?
Index(es):
- Date
- Thread